Z-Wave Plus Aeotec Нано выключатель с измерением электроэнергии
Single Relay switch module to control loads up to 10A.
- Enables Z-Wave control of lights and appliances
- Very small size enables modules to fit into standard switch boxes (45mm recommended)
- Enable for the connection of touch panel
- Supports SPDT (Single-Pole Double-Throw) switches
- Supports the DC24V power input
Nano Switch.
Control any switch.
From anywhere.
Wirelessly.
Power sockets and light switches: amazing inventions. They literally changed the world. But if you’re not standing right next to them or can’t reach them, they’re limited.
No more. The future is smarter. So is your home. Nano Switch offers complete wireless control of your switches and sockets.

Total control.

Nano Switch offers total control, easily. Impossibly small, each Nano Switch installs invisibly behind any of your home’s existing switches or power sockets. Simply unscrew the faceplate, install Nano Switch behind it, and you now have complete wireless control. Your old switches are instantly modern and instantly connected.
Nano Switch is a part of Aeotec’s Z-Wave switch and dimming range and is compatible with light switches and power outlets.
Power outlets. Turn your electronics off in the event of an emergency or a hazard. Smart Switch 6 lets you automatically turn off devices, such as leaking air conditioners and fridges, when then fail. |
Light switches. Monitor and understand exactly how much money the devices plugged into Smart Switch 6 are costing you to run, then create a schedule to reduce your electricity bill. |
Total ability.
Once installed behind a switch or socket, Nano Switch offers unparalleled wireless control via Z-Wave Plus. It lets you control, automate, and monitor your lights light and power sockets. From anywhere. Anytime. And it does it all through enhancement – with Nano Switch, your sockets and switches don’t have to be replaced and they’ll continue to offer the same manual control that you’re used to.
Automation and scheduling. |
Energy metering. |
Remote control. |
Existing control. |
Total home.
Nano Switch is a tool. Installed it minutes, it lets you control, monitor, automate, and schedule the electronics in your home. There’ll be the electronics you use every day; your lights, appliances and entertainment systems. But there’ll also be the electronics that become a part of your smart home as it grows; security and safety devices, electronics indoors and out. If there’s a reason to automate it, to monitor it or make it responsive, Nano Switch is the invisible, controlling, and responsive touch.

Twice the control.
Dual Nano Switch.

Look around your home. Some lights have more than one switch. Some power outlets have more than one socket. For double gang outlets and switches, there’s Dual Nano Switch. Wire it into two switches or sockets for twice the control, twice the energy monitoring, and control of up to 5 amps / 1150 watts per switch channel.
What it doesn’t do.
Nano Switch is incredibly powerful and it’s been designed to control a lot of power. To be this small and control so much, it can’t offer every possible feature. Fully compatible with standard indoor and outdoor bulbs, there are two major things that Nano Switch can’t do: dim lights and work without a neutral wire. But perfect lighting is still only a touch away with Aeotec’s lighting-design focussed Nano Dimmer.

Works with any
socket or switch.

But what it does do is work with any socket or switch in your home. Nano Switch doesn’t change how your home looks by changing your switches, it changes how your home feels by making it far more capable. Nano Switch works with your existing switches and sockets, can be controlled and scheduled by a Z-Wave gateway and app, and can be controlled by other Z-Wave devices including WallMote and WallSwipe.

Perfectly small.
Nano Switch installs behind your home’s switches or sockets. To do that, Nano Switch has to be small. Really small. It is.
60% smaller than the first Micro Smart Switch that Aeotec pioneered, and measuring only 19.5mm / 0.77” in depth, Nano Switch has been designed to be easily installed into even the smallest of junction boxes behind a switch or outlet.
![]() Micro Smart Switch |
![]() Micro Smart Switch 2E |
![]() Nano Switch |

Perfectly safe.
Nano Switch installs behind your home’s switches or sockets. To do that, Nano Switch has to be small. Really small. It is.
60% smaller than the first Micro Smart Switch that Aeotec pioneered, and measuring only 19.5mm / 0.77” in depth, Nano Switch has been designed to be easily installed into even the smallest of junction boxes behind a switch or outlet.
Inbuilt surge |
AES-128 bit |
Perfectly upgraded.
Powerful control. |
Safely small. |
See your spend. |
Gen5. |
Stronger signal. |
Wireless updates. |
Safe wiring. |
Easier wiring. |
Secure control. |
Full scheduling. |
DIN rail compatible. |
Low voltage too. |
Чем больше диапазон действия, тем более надежным является продукт - устройство имеет первоклассную антенну. Оптимизированное для надежности, это устройство может взаимодействовать беспроводным способом на расстояния более 150 метров.
Лучше антенна. Лучше Z-Wave. Устройство разработано на технологии Z-Wave Plus последнего 5го поколения, чтобы предоставить вам самое быстрое время отклика и оптимальное время жизни батареи между перезарядками.
Если вы используете устройство для обеспечения безопасности, вы хотите чтобы взаимодействие было защищенным. Вот почему устройство использует беспроводное шифрование AES-128 для защиты от несанкционированного доступа и хакеров.
Используете ли вы устройство для комфорта или безопасности, вы желаете чтобы оно всегда оставалось обновленным до последней версии. Как бы не создавались обновления прошивки для устройства, вы всегда можете обновить его с помощью Microsoft Windows или выбрать Z-Wave контроллер.
Technical Specification
- MODEL NUMBER
- ZW139
- HARDWARE
- Z-Wave Chip 500 series
- Switching:
- COMMUNICATION PROTOCOLS
- Z-Wave Plus
- FEATURES
- Enable for the connection of touch panel
- Supports SPDT (Single-Pole Double-Throw) switches
- Supports the DC24V power input
- LED AND BUTTONS
- LED indicator
- Include/Exclude button
- ASSOCIATION GROUP
- Four groups and five devices (nodes)
- MAXIMUM CURRENT
- 1 X 10A / 230VAC
- 1 X 10A / 24VDC
- MAXIMUM LOAD
- 2300W (230VAC) (Resistive)
- 240W (24VDC) (Resistive)
- (Resistive-Inductive)
- (Resistive-Capacitive)
- POWER MEASUREMENT
- N/A
- OVERCURRENT PROTECTION
- Required external circuit breaker
- DIMENSIONS
- Package: 50 x 50 x 22 mm (LxWxH)
- Unit: 42.5 x 40 x 20 mm (LxWxH)
- CERTIFICATIONS
- FCC, Z-Wave
- POWER SUPPLY
- AC 120-240VAC, 50-60Hz
- 24 VDC
- POWER CONSUMPTION
- up to 0.8W
- RADIO SIGNAL POWER
- up to 1mW
- RANGE
- up to 50m (outdoors) and 40m (indoors)
- OPERATIONAL TEMPERATURE
- 00-40°C
- FOR INSTALLATION IN BOXES
- D ≥ 60mm, depth ≥ 60mm
- IP CODE
- IP20
- WEIGHT
- Net: 28 g
- Gross: 34 g
Package content
- Unit
- User manual
Z-Wave Specification
Z-Wave Association Capabilities
Model: Nano Switch (ZW139-C)
Z-Wave Certification Number: ZC10-17035523
Group ID |
Maximum Nodes |
Description |
1 | 5 | Z-Wave Plus Lifeline. When the load state of Nano Switch (turn on/off the load) is changed, the Hail CC and Basic Report (configured by parameter 80) can be sent to the associated nodes in this group. |
2 | 5 | Forward the Basic Set, Switch All, Scene Activation Set to associated nodes in Group 2 when the Dual Nano Switch receives the Basic Set, Switch All, Scene Activation Set commands from main controller. (E.g. Send/forward Basic Set to control the other nodes in association Group 2) |
3 | 5 | Send Basic Set (configured by parameter 0x51 ) to the associated nodes in Group 3 when the external switch S1 is operated. Note: The Switch Mode of external switch S1 should be identified successfully, which means that the value of Configuration parameter 0x78 should be non-zero, then the Basic Set can be sent to the associated nodes in Group 3 via triggering the S1 switch. |
4 | 5 | Send Basic Set (configured by parameter 0x52) to the associated nodes in Group 4 when the external switch S2 is operated. Note: The Switch Mode of external switch S2 should be identified successfully, which means that the value of Configuration parameter 0x79 should be non-zero, then the Basic Set can be sent to the associated nodes in Group 3 via triggering the S2 switch. |
Z-Wave Configuration Capabilities
Model: Nano Switch (ZW139-C)
Z-Wave Certification Number: ZC10-17035523
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
120 | 1 | Configure the external switch mode for S1. | 2 | 3 way switch mode | |
0 (Default) |
Enter automatic identification mode | ||||
1 | 2-state switch mode | ||||
3 | Momentary push button mode | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
121 | 1 | Configure the external switch mode for S2. | 0 (Default) |
Enter automatic identification mode | |
1 | 2-state switch mode | ||||
2 | 3 way switch mode | ||||
3 | Momentary push button mode | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
122 | 1 | Set the control destination for external switch | 1 | control the output loads of itself. | |
2 | control the other nodes | ||||
3 (Default) |
control the output loads of itself and other nodes. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
20 | 1 | Configure the output status after re-power on it. | 1 | Always on | |
0 (Default) |
Last status | ||||
2 | Always off | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
252 | 1 | Lock/unlock configuration parameters | 0 (Default) |
Unlock | |
1 | Lock | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
255 | 4 | Reset the Nano Switch | 1431655765 | Reset to factory default setting and removed from the z-wave network | |
0 (Default) |
Reset all configuration parameters to factory default setting | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
4 | 1 | Overheat protection. | 0 (Default) |
Disable | |
1 | Enable | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
80 | 1 | To set which notification would be sent to the associated devices (Group 1) | 0 | Send Nothing | |
1 | Send Hail CC | ||||
2 | Send Basic Report CC | ||||
3 (Default) |
Send Hail CC when using the manual switch to change the load state. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
81 | 1 | To set which notification would be sent to the associated nodes in association group 3 | 0 | Send Nothing | |
1 (Default) |
Send Basic Set CC | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
82 | 1 | To set which notification would be sent to the associated nodes in association group 4 | 1 (Default) |
Send Basic Set CC | |
0 | Send Nothing | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
83 | 1 | Configure the state of LED when it is in 3 modes | 0 (Default) |
Energy mode. The LED will follow the status (on/off). | |
2 | Night light mode. The LED will remain ON state. | ||||
1 | Momentary indicate mode. When the state of Switch’s load changed, the LED will follow the status (on/off) of its load, but the LED will turn off after 5 seconds if there is no any switch action. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
84 | 4 | Set the ON/OFF time of the LED when it is in Night light mode. | 0 to 60 | The minute time of OFF | |
256 to 316 | The hour time of OFF | ||||
65536 to 65596 | The minute time of ON | ||||
16777216 to 16777276 | The hour time of ON | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
86 | 4 | Set appointment 1 | 0 to 60 | The minute value of ON time | |
65536 to 65543 | The day value (Mon to Sun) | ||||
16777216 | Enable the setting. | ||||
256 to 316 | The hour value of ON time | ||||
16777215 | Disable the setting. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
87 | 4 | Set appointment 2 | 256 to 316 | The hour value of ON time | |
65536 to 65543 | The day value (Mon to Sun) | ||||
16777215 | Disable the setting. | ||||
0 to 60 | The minute value of ON time | ||||
16777216 | Enable the setting. |
Z-Wave Command Classes
Model: Nano Switch (ZW139-C)
Z-Wave Certification Number: ZC10-17035523
Supported Command Classes |
All Switch |
Association Group Information |
Association V2 |
Basic |
Clock |
Configuration |
Device Reset Local |
Firmware Update MD V3 |
Manufacturer Specific V2 |
Notification V4 |
Powerlevel |
Scene Activation |
Scene Actuator Configuration |
Security |
Switch Binary |
Version V2 |
Z-Wave Plus Info V2 |
Controlled Command Classes |
Basic |
Hail |
Z-Wave Plus: | No |
---|---|
Z-Wave аппаратная платформа | ZM5101 |
Z-Wave тип библиотеки | Enhanced 232 Slave |
Z-Wave тип устройства | On/Off Power Switch |
Z-Wave тип роли | Always On Slave |
Технология | Z-Wave+ |
Внутренняя/наружная установка | Внутренняя |
Производитель | Aeotec |
Группы ассоциаций | 4 |
Z-Wave Функции | Запуск сцен, Multichanel , Multichannel Association |
Поддерживаемые типы выключателей/управления | Кнопочный, Тумблерный, Кулисный, Без подсветки |
Максимальная нагрузка | 10A |
Тип диммера и выключателя | вставной модуль |
Источник питания | Кабель AC, Блок питания DC |
Тип проводной системы | 3-проводная |
Тип вставного модуля | Реле - 1 нагрузка |
Функции вставных модулей | Дополнительные входы, Измерение мощности, Питание от DC блока, Измерение мощности за период |
Форм-фактор | Настенный |
Назначение | Управление освещением |
OTA обновление прошивки | Yes |